Filaments Details
Wires
Physical quality of wires
| Wire type | S | S-T | SS | BS | ZS | B |
| specific gravity a/cm³ | 7.85 | 7.85 | 7.9 | 7.85 | 7.85 | 8.5 |
| tensile strength up to m/mm² | 2000 | 2100 | 2300 | 2600 | 1600 | 900 |
| temperature stability (in℃) | 300 | 350 | 450 | 300 | 300 | 180 |
*at wire size 0.30
**at continuous load
Chemical resistance(at 20℃)
| ■=permanent |
| ■=comditionality stable |
| ■=unstable |
| Wire type | |||||||
| C3H4O2 | ethanoic acid 10% | S | S-T | SS | BS | ZS | B |
| C3H4O2 | ethanocic acid 80% | ■ | ■ | ■ | ■ | ■ | ■ |
| HNO3 | nitric acid 90% | ■ | ■ | ■ | ■ | ■ | ■ |
| HCL | hydrochiorid acid 2% | ■ | ■ | ■ | ■ | ■ | ■ |
| H2SO4 | sulphuric acid 1% | ■ | ■ | ■ | ■ | ■ | ■ |
| KOH | caustic potash 50% | ■ | ■ | ■ | ■ | ■ | ■ |
| NaOH | caustic potash 20% | ■ | ■ | ■ | ■ | ■ | ■ |
| ketone,ester | ■ | ■ | ■ | ■ | ■ | ■ | |
| benzene,benzine | ■ | ■ | ■ | ■ | ■ | ■ | |
| Soft B Brass wire(CuZu) | ■ straight crimped,dia.0.06mm to 0.50mm |
| Medium S Steel wire,matural | ■ hard,crimped,dia.0.06mm to 0.80mm |
| ZS Zinc-coated steel | ■ wire,natural hard straight,dia.0.30mm to 1.00mm |
| BS Brass-coated steel | ■ wire,single wire,springy,crimped, dia.0.15mm to 0.38mm |
| SS Stainless steel wire. | ■ acid resistant,crimped or straight,dia. 0.15mm to1.00mm |
| Hard S-T Steel wire,tempered | ■ straight,dia.0.30mm to 1.20mm |
The most important characteristic for the quality of brush wire is the tensile strength,which determines the abrasion-proof,hardness and cutting duty of the wire brush,The list beside details the wires that are more frequently used today and the table above details the chemical and physical qualities.The indications of the tensile strength refer to a medium wire diameter of 0.3mm.In order to obtain our worle renowned wire quality,we are always in touch with internationally chosen wire manufacturers and thus are in the position to offer you a wide variety of wire qualities for all types of applications.
Abrasive Filaments
Surface speed is a decisive factor in achieving optimum performance from a brush.Please choose the appropriate surface speed on the basis of the materials of the surface,required effects and the power applid.As a general guide,we recommend the following surface speeds when working on the materials listed.Please note: the operating speed should never exceed the maximum RPM ratings for each brush as shown in this catalogue.
Physical quality of abrasive filaments
| Basic maerial | Pa6 | Pa6.12 |
| Specific gravity(cm3) | 1.26 | 1.26 |
| water absorption(%) | 9.5 | 3.0 |
| stiffness in dry operation(PA 6.12=100%) | 90 | 100 |
| in wet operation(PA 6.12 dry=100%) | 40 | 75 |
| resisitance to abrasion(PA 6.12 dry=100%) | 75 | 100 |
| heat resistance in dry operation(℃) | 100 | 110 |
| in wet operation(℃) | 90 | 100 |
As-is round filament with integrated silicon carbide(S I C) grit is used worldwide,We offer grit sizes from 46 to 800,heat stability,a considerable chemical resistance and even grit insertion.
Our basic quality is principally composed of heat resistant basic Nylon material (including all types from Pa6 up to PA 6.12)and a grit percentage of 20 to 40.
Abrasive filaments are especially appropriate for deburring processes and surface treatment of steel, heavy metals,aluminum and even wood.
WHY DO WE REACH FURTHER?
Because of the need for innovation to provide you with the perfect solution
ABOUT US
PRODUCTS
2017-2020 Beilun Futuo Mechanical Tools Co., Ltd.
Support:seerp Inc.
浙公网安备 33020602000424号